Wiimote Repair
Written by eipromb on April 22, 2008 – 1:37 pm -If you’ve have managed to break your wiimote in attempts to perform the Player Indicator Mod, or are just too scared to break your wiimote to do it, this guide is for you. The most likely scenario is that you ripped off a pad or two, but this guide also covers dead wiimotes and wiimotes with the IR sensor not functioning.
What you’ll need:
A Triwing Screwdriver
Soldering Iron and Solder
Desoldering Braid
Isopropol Alcohol
Tooth Brush
30 Gauge Wire
Step 1:
So here’s an example of a broken wiimote.
Step 2:
I’ve used the Isopropyl alcohol and a toothbrush to scrub off all the residue flux from the board giving a clean surface to start from.
Step 3:
Use the desoldering braid to clean up the pads, try not to apply too much pressure or heat or you’ll end up damaging or lifting them. The proper way to do it is to gently place the iron on the braid then slide the braid back on forth holding the other end of the braid. This is to remove any of the excess solder from the pads, also what happens is when you place too much heat and time on the joint you get something called intermetallic growth which weakens the joint.
Step 4:
At this point I would solder the LEDs on to complete the mod you’re performing. If there are any missing pads use this wiring diagram to run 30 gauge to the correct points. If you’ve managed to damage any of the resistors (outlined in white) you’ll need to replace them, they are 0402 470ohm resistors.
Step 5:
If for some reason you can’t solder to the vias near the ‘button 2′ pad, you’ll be able to run them directly to the controller.
Step 6:
If you’ve managed to solder everything on okay but your wiimote just doesn’t turn on any more, check the board for solder splashes and solder balls that may be causing shorts.
Step 7:
Once you’re sure that your board is clean, check the fuse pictured below. With a multimeter the fuse should read around 1 ohm, if the fuse has blown usually from the shorts in step 6, the fuse will need to be replace (safer) or jumpered (cheap).
Step 8:
From what I’ve seen the culprit to a non-functional IR sensor is mistake performing the Easy A Button Backlight Mod or the Nunchuck LED Backlight Mod. This can be verified by removing the LED from the board and checking the wiimote, once verified reperform the mod being careful not to cause any shorts. A note to remember is that the shorts maybe caused by the plastic housing pressing down on the exposed part of the LED.
Conclusion:
I hope this helps many of you attempting to perform the mods here on this site. If you still need help or are stuck in a situation that doesn’t apply to you, discuss it in the forums. There are lots of people there willing to help you out.
Tags: repair, wiimote
Posted in Guides |
August 31st, 2008 at 2:41 pm
wow this guide was so useful! i blew the fuse shown in step 7 and i was soooo scared my wiimote was gone, but if you know, what kind of fuse is it?? will any fuse with a 1ohm reading do?? and is it safe to jump it?? cuz i jumped it and it seems to work fine… but what will happen if i short sumthing again?? will that be the real death of my wiimote or can the circuit bored handle that kind of short??
ps any ideas on how to fix a broken clip??
(after successfully prying the case off, i dropped the top and broke one clip, lol, super glue maybe???)
February 22nd, 2009 at 8:44 pm
omg thank you!!! you saved my wiimote!!!
June 29th, 2009 at 3:36 am
hey, i blew my wiimote fuse,too.
i tried to jump it but when i did it,
the small smd lights didnt glow very bright. i only could see them when i was in a dark room.
i didnt do any kind of mod with my wiimote i just blew my fuse.
i tried to jump it wit different wires for example solder or a normal wire. please help i dont want to buy a new wiimote.
leo
(sorry for my bad english i’m german)
April 12th, 2010 at 9:18 am
Я могу проконсультировать Вас по этому вопросу. Вместе мы сможем прийти к правильному ответу….
Заместитель главного бухгалтера The most likely scenario is that you ripped off a pad or two, but this guide also covers dead wiimotes and wiimotes […….
May 19th, 2010 at 7:01 am
Жаль, что не смогу сейчас участвовать в обсуждении. Не владею нужной информацией. Но с удовольствием буду следить за этой темой….
…
June 25th, 2010 at 5:31 pm
Pillspot.org. Canadian Health&Care.Special Internet Prices.No prescription online pharmacy.PillSpot.org. Herbal-supplements@buy.online” rel=”nofollow”>.…
Categories: Eye Care.Skin Care.Mental HealthStop SmokingAntidiabetic.Antidepressants.Womens Health.Weight Loss.Vitamins/Herbal Supplements.Anxiety/Sleep Aid.Antiviral.Mens Health.Pain Relief.Blood Pressure/Heart.Stomach.Antibiotics.Anti-allergic/A…
August 29th, 2010 at 2:31 am
quote http://google.com : Love this keyword…
google…
August 29th, 2010 at 2:54 am
Supplement http://APTAUTOPARTS.INFO/tag/Dietary Supplement Fact Sheet : Supplement…
google…
August 29th, 2010 at 3:08 am
60 E80 e80/ http://02JEEPPARTS.US/tag/E : 60 E80 e80/…
60 E80 e80/…
August 29th, 2010 at 4:05 am
uk MacBook Apple/ http://AWESOMEBABYCLOTHES.INFO/tag/r\x3dh : uk MacBook Apple/…
uk MacBook Apple/…
August 29th, 2010 at 6:20 am
light http://bindoorbpgz0.copious-systems.com/tag/application light guard/ : light…
light…
August 29th, 2010 at 6:30 am
Popular http://vpopularj9k1.AUTOPARTSTHAI.INFO/tag/Cologne+womens+Popular/ : womens…
womens…
August 29th, 2010 at 5:28 pm
stereo http://jpcfx.02JEEPPARTS.US/tag/laptop+pc+stereo/ : stereo…
stereo…
August 29th, 2010 at 5:36 pm
memory http://mavonqjnl.BABYCLOTHESNUT.INFO/tag/memory+Operating+upgrades/ : memory…
memory…
August 29th, 2010 at 5:39 pm
northern http://dnortherns63.AACEHARDWARE.INFO/tag/Pictures+Lights+northern/ : northern…
Lights…
August 29th, 2010 at 9:53 pm
parts http://fair0mpfctr.AUTOTECHGUIDE.INFO/tag/Parts+parts+airstream/ : airstream…
Parts…